Dacor Dishwasher RDW24S User Manual

RDW24I, RDW24S  
Document # PG10-007  
Revised 03/12/12 Page 1/3  
PLANNING  
GUIDE  
Renaissance® 24” Wide  
Built-In Dishwasher  
Product tolerances: ±1/16” (±1.6 mm)  
otherwise stated  
Product Dimensions  
WaRnIng  
Observe all governing codes and ordinances during planning  
and installation. Contact your local building department for  
further information.  
A
This appliance must be installed in accordance with the  
accompanying installation instructions.  
Model RDW24I  
Model RDW24S  
Stainless steel  
24” (61.0 cm)  
Integrated  
approximate  
Shipping Weight  
Front Panel Type  
(A) Width  
front panel2  
Front  
23 1/2” (59.7 cm)  
B
117 lbs. (53 kg.)  
7/8” (86.0 cm) to  
/2 (92.7 cm)4  
34 3/8” (87.4 cm) to  
36 1/2” (92.7 cm)  
(B) Height  
(C) De
8.1 cm)5  
22 7/8” (58.1 cm)  
ith  
uration  
Epicure®: 2 1/2” (6.4 cm)1  
Millennia®: 2” (5.1 cm)2  
(D) H
1 EHCH (chrome) or ADWE24HB (glossy black)  
M24H (polished) or ARDWMH24 (brushed)  
es installation of either a Dacor glass panel kit  
or dealer), or a customer provided, custom overlay  
om overlay panel allows you to blend the exterior of  
r into the overall kitchen décor. See page 2/3 for more  
Depth with door open  
49 3/4” (126.4 cm)  
Depth with door closed  
C
D Handle depth  
ith required trim kit installed.  
ut custom front panel installed.  
Drain hose  
Do not modify  
loop in hose  
nit  
Side  
Drain hose  
54” (137.0 cm)  
long  
Back  
6 1/4” (15.9 cm) to  
8 1/4” (21.0 cm)  
Water supply line  
60” (152.0 cm)  
long  
Power cord  
44” (112.0 cm)  
long  
1 15/16” (4.9 cm)  
3 3/8” (8.6 cm)  
2 7/8” (7.3 cm)  
UtILIty CoNNECtIoN DImENSIoNS  
B
B
C
A
C
A
A = 7/8" (2.2 cm) B = 18 1/2" (47.0 cm) C = 2 3/8" (6.0 cm)  
A = 1 3/8" (3.5 cm) B = 23" (58.40 cm) C = 2" (5.1 cm)  
mILLENNIA StyLE hANDLE DImENSIoNS  
(PARt NUmBERS ADWm24h AND ARDWmh24)  
EPICURE StyLE hANDLE DImENSIoNS  
(PARt NUmBERS ADWE24hCh AND ADWE24hCh)  
All specifications subject to change without notice.  
Phone: (800) 793-0093  
 
RDW24I, RDW24S  
Document # PG10-007  
Revised 03/12/12 Page 3/3  
PLANNING  
GUIDE  
Renaissance 24” Wide  
Built-In Dishwasher  
Drain Specifications  
Custom Panel/Handle for Model RDW24I  
IMPORTanT: Should a drain hose longer than the one provided be  
required, use a hose extension approved for detergents and high  
temperature water. Total drain hose length (including factory installed  
hose) must not exceed 10 feet. (304.8 cm) from the top of the drain loop  
on the back of the unit. Joints and joint tubes must have a minimum inside  
diameter of 7/8” (2.2 cm).  
The custom panel mounting screws are provided with the dishwasher.  
Follow the panel dimensions below to ensure that the custom overlay  
panel will fit properly.  
The handle and handle mounting hardware are not included with  
model RDW24I. A handle designed for use with an appliance should  
produce satisfactory results. Do not use a knob or handle attached  
by a single fastener. Instead use a handle with a larger D-style  
pull. The panel craftsman must determine and obtain the proper  
handle fasteners for the application. Handle screw heads must be  
countersunk into the panel before panel installation.  
The drain hose supplied with the dishwasher must be connected to  
a minimum 1/2” inside diameter drain connection. The drain hose is  
equipped with a cone-shaped connector on the end that is ready to be  
cut to the desired drain connection size. Only a clamp (not provided)  
is required. It fits drain connections with an internal diameter of 1/2,  
5/8, 3/4 and 7/8 inches (1.3, 1.6, 1.8 and 2.2 cm).  
(g) Height  
(H) Width  
(J) Thickness  
30 1/8” (76.5 cm)  
23 3/4” (60.3 cm)*  
3/4” (1.9 cm) min.  
You must install an air gap in the drain system if required by local  
codes. Plan for the air gap in the sink or countertop area adjacent to  
the dishwasher. A section of drain hose (not provided) needs to be  
installed from the air gap to the waste disposer inlet or waste tee. See  
below.  
* Based on 24” (61de cutout. Recommended panel width is 1/4”  
(6.4 mm) less th.  
IMPORTanghs more than 15 pounds, you must  
order the rings (Dacor PN 701385). Maximum  
panel wgs: 23 pounds.  
If an air gap is not required, the drain hose must be installed to a  
disposer inlet or waste tee above the sink trap in the household  
plumbing.  
For proper drainage, the drain line connection must be a minimum  
of 20” (50.8 cm) above the bottom of the dishwasher. No part of the  
drain hose can be lower than the disposer or waste tee connection
higher than 35” (88.9 cm) from the bottom of the dishwasher.  
G
CUStom PANEL  
DImENSIoNS  
ax.  
20"  
min.  
H
J
ExAmPLE oF DRAIN CoNNECtIoN WIthoUt AIR GAP  
35"  
max.  
20"  
min.  
ExAmPLE oF DRAIN CoNNECtIoN WIth AIR GAP  
All specifications subject to change without notice.  
Phone: (800) 793-0093  
 

Cisco Systems Network Router 2600XM Series User Manual
Continental Electric Rice Cooker CE23261 User Manual
Continental Iron CP43021 User Manual
Craftsman Saw 31521234 User Manual
Edelbrock Automobile Parts 1207 User Manual
FEIN Power Tools Trimmer BLs 25 User Manual
Fender Camcorder Accessories PD 150 User Manual
Garland Cooktop GIU 18 User Manual
GE Ventilation Hood ZV30R User Manual
GE Waffle Iron 169118 User Manual